I need to log fuel pressure for some trouble shooting. I took an old O2 sensor and cut the pigtail off and made a jumper harness over to my fuel pressure sensor. I changed my settings in ECMlink to simulate front O2, and set my front O2 input to linear fuel pressure. My voltage parameters were...

I have a few questions about how to build my spare transmission. I just purchased rebuilt gear clusters that Jacks did in 2017, they were never installed. It includes an EVO3 input shaft and first gear. The transmission case vin shows its a 91, with the later shift levers. Intermediate shaft...

just a heads up, while browsing e-bay I found a listing for a new 95-99 gst transmission. I'm sure someone could use it

1). No boost, vac, or exhaust leaks. compressor housing leaks a little2). Verify mechanical timing. New belt, oem tensioner, pulleys3). Verify base timing set4). Ignition system new wires and plugs gapped at 26. BPR7ES5). Motor health 160 psi compression6). Basic throttle body...

This is the Build Thread for 1992 Eagle Talon. Reply below.

any one know where the other connector is?? my car is a 97 turbo talon. I have tore half the car apart and still cant find it.

Looking to do some upgrades just seeing what you guys thought.evo III 16g and o2 housing 660s safc 190 fuel pump 2g mas FMIC haven’t decided on one yetWill the 190 supply enough fuel? Also will I have any problems running the injectors with the Safc? I heard they are a little...

car is a early 95 GSTI have been having problems with my friends car. I put a used head on it and could not get it running right. He took the car to a shop. they replaced the Isc on it and the said it has the wrong intake manifold on it. the could not get it to seal.no matter what year...

this will be my first winter with my awd. I was wondering how well they get around in the snow with out snow tires? I have a good set of tires but if I dont need them I was just going to sell them. How many of you run with out them?

I have been getting a rough idle and white smoke the last couple of days. it seems to happen when the car is warm. like after 20 min of driving, also I get a lot of water spewing out of the overflow tank. I checked compression and the are all 150. I looked for water in the oil and oil in the...

Hey guys, My car died right after I changed my clutch. It was like everything just shut down. I reset the computer and it started right up. About a week later it did it again and I had to let the car sit over night and it started up again. It did it again but this time it won’t start. I am not...

hey guys I was wondering if any one knows of a good place to buy a used engine. I will be putting one in my friends 95 turbo FWD that he just bought. also the build date is 94 on the car.

My cars oil pressure is really low when I come to an idle. It slowly goes down. It does not seem to affect anything. Should I get a new sender and see if that helps. Also it seems to be fine when going down the road.

Sorry it’s long.Has any one ever bought anything from ram chargers?? I am not real happy with them. I ordered Arp head studs and rod bolts from them three weeks ago. They told me they were both out of stock which was fine. I called them a week ago to see if they had gotten them in yet...

Right now I am rebuilding my 6 bolt for my Laser. I ordered Arp head studs and rod bolts. Right now the heads studs are 4 weeks away and the rod bolts should be here soon. Do I really need the head studs? As of now I will be stock. But in the future I plan on adding a bigger turbo and the...

Does any one know what year of Mirage 1.6L the balance shaft eliminator kit parts are from?? My As***** of a mitsubishi dealer will not sell me the parts with just the part numbers. He wants to know what year it the parts are from. He knows I have a laser and said they wont work.:cry:

hey guys, I just got a call from my mahine shop and the said my block would not clean up at .020 over. The next size of pistons are .040 over.(where I got them at) am I going to have problems doing this? or should I look for some .030 over pistins?

what should I expect the cost of getting the pistons put on the rods?